DIY router build
-
I think I should specified that my current router died a few days ago and that's one of the reasons I wanted to start with a DIY router. Because a few people said that I should not tinker on my network edge, I went ahead and bought a ASUS WiFi 6 Router (RT-AX3000) on Amazon. At the same time, others said that a DIY option can be around or a little more than a COTS router, so it's worth it to just go that route and dump the COTS router.
I bought the ASUS router yesterday on Amazon so it hasn't shipped yet and I was thinking if I can figure out my plan for the DIY router, then I could potentially just cancel that order asap. With that said, I'll continue below.
@scottalanmiller - Were you referring to something like this?
https://www.gateworks.com/products/industrial-single-board-computers/imx8-single-board-computers-gateworks-venice/Or if using the Seeedstudio link you shared, then maybe this?
Sample complete SBC build:If not, could you spec out a complete build if you have a moment, please?
Also, regarding purchasing from seeedstudio, I must admit I'm quite nervous since the dropdown box for me only shows "CN warehouse" which means it would ship direct from China. My worries are risk about customer support if I receive a lemon, lack of documentation/user manual, shipping, etc. But if you meant the gateworks link, then it should be ok although the price isn't listed for their product offerings.
@krzykat - I considered a Qotom box, but was nervous about direct shipping from China as indicated above in my response to Sam.
@Pete-S - Are you referring to something like this?
https://metebalci.com/blog/home-lab-server-2022/If so, this may be a bit much for me personally. The cost isn't a big issue even though this is expensive, but rather having to build an entire separate PC tower unit is likely not an option for me currently. My studio is less than 160 sq ft, so space is very limited here. Also, a server like in the link above would very likely consume a ton of wattage and my building only allows a certain amount of total wattage from each studio. This server would eat too much power unfortunately. But I can definitely return to this after I have moved into a new place (or ideally, have purchased an apartment/house). OR if you have a low wattage idea, then, nevermind what I typed above.
-
@Johann said in DIY router build:
@Pete-S - Are you referring to something like this?
https://metebalci.com/blog/home-lab-server-2022/
If so, this may be a bit much for me personally. The cost isn't a big issue even though this is expensive, but rather having to build an entire separate PC tower unit is likely not an option for me currently. My studio is less than 160 sq ft, so space is very limited here. Also, a server like in the link above would very likely consume a ton of wattage and my building only allows a certain amount of total wattage from each studio. This server would eat too much power unfortunately. But I can definitely return to this after I have moved into a new place (or ideally, have purchased an apartment/house). OR if you have a low wattage idea, then, nevermind what I typed above.No, something like this:
Any Intel NUC. They're small and all models are low power. You just need to put in enough memory and SSD to run some virtual machines. 32GB RAM will do it. -
@Johann said in DIY router build:
I think I should specified that my current router died a few days ago and that's one of the reasons I wanted to start with a DIY router. Because a few people said that I should not tinker on my network edge, I went ahead and bought a ASUS WiFi 6 Router (RT-AX3000) on Amazon. At the same time, others said that a DIY option can be around or a little more than a COTS router, so it's worth it to just go that route and dump the COTS router.
No, you need a working internet connection first to build anything. Any router would get that job done though.
Pros in general prefer a standard router/firewall with no wifi and then one or several access points to provide wifi. For example Edgerouter ER-X and any access point (if you need wifi).
In your case with that small space I'd probably just buy a $50 wifi router and be done with it. No point in buying a more expensive wifi router - better to buy the pro stuff in that case.
So I'd just cancel the amazon order and order a cheaper wifi router instead or go the pro route.
-
I'm with Pete here.
Buy an Edgerouter-x for your primary home firewall/router. Then decide what you want for WiFi - I've been using Unifi APs for nearly a decade with little to no issues.
As for your learning - physical hardware is really mainly good for learning hypervisors, beyond that you could do everything in a VPS provider like Vultr. No upfront fees, no power drain on you at all. I'm not sure what they offer on the networking side, i.e. you setting up your own private network playground where you setup a router on the edge, etc... but the other typical server stuff they can definitely provide like any other VM would.
-
@Dashrender said in DIY router build:
As for your learning - physical hardware is really mainly good for learning hypervisors, beyond that you could do everything in a VPS provider like Vultr. No upfront fees, no power drain on you at all. I'm not sure what they offer on the networking side, i.e. you setting up your own private network playground where you setup a router on the edge, etc... but the other typical server stuff they can definitely provide like any other VM would.
While providers such as Vultr would be good for running production I don't think it's ideal for a homelab. You really want to be able to spin up many VMs without the cost immediately running away.
You could potentially sign up for a bare metal server but then it's from $120 per month from Vultr. I know Hetzner (Europe) has among the cheapest bare metal servers and you could probably find something for $50 per month.
Just checked and found something:
But latency might be a killer from the US. -
@Dashrender said in DIY router build:
As for your learning - physical hardware is really mainly good for learning hypervisors, beyond that you could do everything in a VPS provider like Vultr
Well, why use Vultr with the monthly costs when you could learn it ON the hypervisor you are also learning on the bare metal?
-
@scottalanmiller said in DIY router build:
@Dashrender said in DIY router build:
As for your learning - physical hardware is really mainly good for learning hypervisors, beyond that you could do everything in a VPS provider like Vultr
Well, why use Vultr with the monthly costs when you could learn it ON the hypervisor you are also learning on the bare metal?
Of course - if you have the hardware, then sure, if you don't...
-
@Pete-S said in DIY router build:
No, you need a working internet connection first to build anything.
I have internet connectivity since I can always just connect directly via the modem.
Can you tell me more about the Intel NUC option, please? I'd just need a case, memory and SSD, yes? Any good sample builds that come to mind?
I'm still curious about the SBC option Sam mentioned and would like to fully look into that as well. I'm trying to read up on it now.
-
@Johann said in DIY router build:
Can you tell me more about the Intel NUC option, please? I'd just need a case, memory and SSD, yes? Any good sample builds that come to mind?
There is nothing to build. It's often sold as a barebone, meaning you buy whatever memory you need and whatever SSD you want, plug it in and you're good to go. Youtube is your friend for stuff like that.
-
I'd rather use a hardware router
-
@StuartJordan said in DIY router build:
I'd rather use a hardware router
He's doing it for a lab, not for use.
-
@scottalanmiller said in DIY router build:
@StuartJordan said in DIY router build:
I'd rather use a hardware router
He's doing it for a lab, not for use.
Ok fair enough, didn't read the ops post fully.
-
@StuartJordan - You were correct as I will be using the router as my main router instead of a traditional COTS router:
https://mangolassi.it/post/549470My apologies that this wasn't clear in the OP.
I'm currently assembling a parts list for a build or two.
-
@Johann said in DIY router build:
@StuartJordan - You were correct as I will be using the router as my main router instead of a traditional COTS router:
https://mangolassi.it/post/549470My apologies that this wasn't clear in the OP.
I'm currently assembling a parts list for a build or two.
Always fun building it yourself.
-
I'm gonna play devils advocate here, and say it's a complete waste of time to build a hardware lab. If you want to work SMB for 100 employee company, then fine whatever. They want to pay you to monkey around with hardware for a few servers instead of doing Colo or cloud.
Everyone on here giving the advice is passionate about their work and thorough, but unless you want to do IT service work or be one man IT shop, there isn't really any value in this stuff. Get an edge router and buy a cheap hardware device as @Pete-S recommended.
I actually had to check the date a few times on this thread and make sure it wasn't nearly a decade old. Because man this is dated way to learn. You'll find very little of what you want to learn, has to do with hardware or even a specific Colo or cloud. Notice how everyone talked about sever configuration or networking. Neither of those pertain to actual hardware. The implementation you'll be doing in the real world is both hardware and cloud agnostic.
-
@IRJ I know what your saying, let the man play around though
-
@IRJ said in DIY router build:
I'm gonna play devils advocate here, and say it's a complete waste of time to build a hardware lab. If you want to work SMB for 100 employee company, then fine whatever. They want to pay you to monkey around with hardware for a few servers instead of doing Colo or cloud.
Everyone on here giving the advice is passionate about their work and thorough, but unless you want to do IT service work or be one man IT shop, there isn't really any value in this stuff. Get an edge router and buy a cheap hardware device as @Pete-S recommended.
I actually had to check the date a few times on this thread and make sure it wasn't nearly a decade old. Because man this is dated way to learn. You'll find very little of what you want to learn, has to do with hardware or even a specific Colo or cloud. Notice how everyone talked about sever configuration or networking. Neither of those pertain to actual hardware. The implementation you'll be doing in the real world is both hardware and cloud agnostic.
This is why I mentioned going the Vultr route. While there could be some savings in setting up a dozen VMs on a local VM host at his house - it's not accessing like a business generally does anymore - as IRL is mentioning.
-
@Dashrender said in DIY router build:
This is why I mentioned going the Vultr route. While there could be some savings in setting up a dozen VMs on a local VM host at his house - it's not accessing like a business generally does anymore - as IRL is mentioning.
It can be if you set it up that way. To a user, it's hard to tell the difference. Other than "putting in a credit card" most people using cloud experience nothing different than installing a VM on a hypervisor.
-
@Dashrender said in DIY router build:
it's not accessing like a business generally does anymore
IT's still how 90% of business does it. Marketing aside, cloud isn't the majorit of workloads, and the majority of cloud is replicating legacy workloads.
-
@scottalanmiller said in DIY router build:
@Dashrender said in DIY router build:
it's not accessing like a business generally does anymore
IT's still how 90% of business does it. Marketing aside, cloud isn't the majorit of workloads, and the majority of cloud is replicating legacy workloads.
That part definitely seems to be true
