Ubiquiti UniFi AP: Signal drop out issue.
-
@JaredBusch said:
Now, just to make sure your controller readopts it and then monitor for drop outs.
Other than using my Andriod as I have,.. is there a Windows tool that will do the same thing?
-
Cut together scan for about 5 minutes
-
Not going to add another screen shot,.. but showing 5 drop outs in one screen..
Something is not right with this unit.
-
It could be the software... I heard from a lot of folks in the Spiceworks forums that they started having issues with the 3.x series firmware, but the 2.4 ones were good.
-
I just submitted a support request to them. I linked back to this thread -
-
We Tweeted directly to them the other day too. No response from them though.
-
@scottalanmiller said:
We Tweeted directly to them the other day too. No response from them though.
I have a response... but only for some of what I have already given... Screen shot of error? I don't have one really.. just poor signal quality. sigh
-
Your best solution will be another AP to prove issues.
Otherwise, the best you can expect is an RMA that takes 2 weeks. Assuming it is under warranty.
-
@JaredBusch said:
Your best solution will be another AP to prove issues.
Otherwise, the best you can expect is an RMA that takes 2 weeks. Assuming it is under warranty.
Maybe as such as this?
Pulled out a EnGenius AP I happen to have. The main signal on it didn't bounce around. I even walked around and went upstairs and sat just 3 feet away from the UniFi AP.
Dropping the EnGenius power to just 10% didn't seem to drop the signal level much.
-
@JaredBusch said:
Your best solution will be another AP to prove issues.
@g.jacobse said:
Maybe as such as this?
No, you need to get a second UAP to prove a hardware problem or software problem.
If a second UAP does exactly the same thing, then you have a problem with the UniFi software (firmware most likely). If it does not have this problem, then the problem is the hardware. Request a RMA if under warranty and move on.
-
@g.jacobse said:
Dropping the EnGenius power to just 10% didn't seem to drop the signal level much.
A lot of the time that can actually improve signal quality haha
-
Yes, as I mentioned in Skype, I think, pretty much every AP in the world should never be set to high power in a normal residence.
Those power levels will overwhelm the radio in the phone/device.
-
Fewer signals bouncing all over the place.
-
@JaredBusch Yup, most of the AP's you'll see come juiced up too far IMHO
If you're giving up on your unifi AP, maybe try throwing DD-WRT on it for giggles - might be surprised, who knows.
-
-
Requires DD-WRT professional subscription if I understand how DD-WRT works..
-
@JaredBusch said:
@JaredBusch said:
Your best solution will be another AP to prove issues.
@g.jacobse said:
Maybe as such as this?
No, you need to get a second UAP to prove a hardware problem or software problem.
If a second UAP does exactly the same thing, then you have a problem with the UniFi software (firmware most likely). If it does not have this problem, then the problem is the hardware. Request a RMA if under warranty and move on.
Buggers - I have enough hardware around here. Rather avoid another purchase if I can avoid it. Though, I suppose could split coverage of the house, and drop the output power then.
-
@g.jacobse said:
Buggers - I have enough hardware around here. Rather avoid another purchase if I can avoid it. Though, I suppose could split coverage of the house, and drop the output power then.
Assuming it is under warranty, I am sure that you could easily get an RMA approved for your current UAP if you have opened a support case and sent in the screenshots and such.
You will just have to be without it for two weeks or so.
Buying a second was a suggestion to not be without one.
-
@JaredBusch said:
@g.jacobse said:
Buggers - I have enough hardware around here. Rather avoid another purchase if I can avoid it. Though, I suppose could split coverage of the house, and drop the output power then.
Assuming it is under warranty, I am sure that you could easily get an RMA approved for your current UAP if you have opened a support case and sent in the screenshots and such.
You will just have to be without it for two weeks or so.
Buying a second was a suggestion to not be without one.
LOL... I am not AP poor.. If I pulled my gear from the neighbors I'd have to Linksys WAP54G APs, then there is the UniFi AP and the EnGenius..
At one time I had a bridge going to their house to give them internet. But that was some time back and they now have their own service. Bridge is down,.. I just never bothered to go get it. Come to think of it,.. there may be a Linksys wireless router over there too..
-
@JaredBusch said:
Requires DD-WRT professional subscription if I understand how DD-WRT works..
Ahhh too bad
