EdgeRouter X - bridge mode

Mike Davis

I have a client with a EdgeRouter X. They have a phone system that the phone system vendor needs to be able to remote in to once in a while, and they will need to access from the LAN once in a while. They were out of ports on their switch, so I told them to plug in to eth2 and I would configure from there.

eth0 is their LAN, so I figured I just needed to bridge eth0 and eth2. Is that correct? I did that and I can't ping the IP address I told him to use from the LAN so I don't know if my config is wrong, or if he didn't put the IP in correctly.

Here is my config:


ubnt@ubnt:~$ show configuration
firewall {
    all-ping enable
    broadcast-ping disable
    ipv6-receive-redirects disable
    ipv6-src-route disable
    ip-src-route disable
    log-martians enable
    name WAN_IN {
        default-action drop
        description "WAN to internal"
        rule 10 {
            action accept
            description "Allow established/related"
            state {
                established enable
                related enable
            }
        }
        rule 20 {
            action drop
            description "Drop invalid state"
            state {
                invalid enable
            }
        }
    }
    name WAN_LOCAL {
        default-action drop
        description "WAN to router"
        rule 1 {
            action accept
            description "Allow established/related"
            state {
                established enable
                related enable
            }
        }
        rule 2 {
            action accept
            description "allow ssh config"
            destination {
                port 22
            }
            log disable
            protocol tcp
            source {
            }
        }
        rule 3 {
            action drop
            description "Drop invalid state"
            state {
                invalid enable
            }
        }
    }
    receive-redirects disable
    send-redirects enable
    source-validation disable
    syn-cookies enable
}
interfaces {
    bridge br0 {
        address 192.168.1.1/24
    }
    ethernet eth0 {
        bridge-group {
            bridge br0
        }
        description "Local 2"
        duplex auto
        speed auto
    }
    ethernet eth1 {
        address dhcp
        description Internet
        duplex auto
        firewall {
            in {
                name WAN_IN
            }
            local {
                name WAN_LOCAL
            }
        }
        speed auto
    }
    ethernet eth2 {
        bridge-group {
            bridge br0
        }
        description Local
        duplex auto
        speed auto
    }
    ethernet eth3 {
        description Local
        duplex auto
        speed auto
    }
    ethernet eth4 {
        description Local
        duplex auto
        speed auto
    }
    loopback lo {
    }
    switch switch0 {
        address 192.168.2.1/24
        description Local
        mtu 1500
        switch-port {
            interface eth2
            interface eth3
            interface eth4
        }
    }
}
service {
    dns {
        forwarding {
            cache-size 150
            listen-on eth0
            listen-on switch0
        }
    }
    gui {
        https-port 443
    }
    nat {
        rule 5010 {
            outbound-interface eth1
            type masquerade
        }
    }
    ssh {
        port 22
        protocol-version v2
    }
}
system {
    host-name ubnt
    login {
        user ubnt {
            authentication {
                encrypted-password ****************
                plaintext-password ****************
            }
            full-name ""
            level admin
        }
    }
    name-server 8.8.8.8
    ntp {
        server 0.ubnt.pool.ntp.org {
        }
        server 1.ubnt.pool.ntp.org {
        }
        server 2.ubnt.pool.ntp.org {
        }
        server 3.ubnt.pool.ntp.org {
        }
    }
    syslog {
        global {
            facility all {
                level notice
            }
            facility protocols {
                level debug
            }
        }
    }
    time-zone America/New_York
}

BTW, I know ssh is allowed on the external interface. I had to do that since I was working remote and had to remove the address off eth0 so I could assign it the bridge group. I realize now it may have been easier to give him an IP in another subnet and then just add a route between the subnets, but if I'm going to do that, I'll still need to get him on from the outside so he can change the config.

Dashrender

I'm probably talking out of my ass so why not put a switch between ports 0 + 2?
Similar to Ports 3 4 and 5

JaredBusch

Update the firmware to 1.9.1, also apply the bootloader patch if never done.
Is this an ER-X or an ERL? there is a huge difference in what can be done. I assume it is and ER-X since you have up to eth4 in the config.
Of course you can create a bridge, but see below.
You don't need SSH open on the WAN, but if you are going to do that, at least lock it down to your IP. If you are on residential and change a lot, you can still at least lock it down to your ISP's owned block. Check that at arin.net.
Your problem is you have eth2 on both switch0 and br0. I am surprised it even let you commit that.
This config is non-standard. UBNT standards are WAN on eth0 and then go from there.
I hope this a very redacted config. If not, then go on site and run the first setup wizard again (may not have existed when deployed originally).
If you don't do anything I said, then delete the bridge and put eth0 on switch0 along with everything else. Don't forget to change the IP on switch0 to be what you had on eth0 before you made it br0.

JaredBusch

I would recommend that you wipe and start over using standard port layout.

You can easily reprogram everything by grabbing the output from show configuration commands

Mike Davis

@JaredBusch said in EdgeRouter X - bridge mode:

I would recommend that you wipe and start over using standard port layout.

You can easily reprogram everything by grabbing the output from show configuration commands

I'm headed in... Any reason not to run the WAN+2LAN2 wizard?

Dashrender

Is this an ER-X or a ER-L?

Mike Davis

@Dashrender ER-X

Dashrender

If they don't have a WAN + Switch0, then yeah I'd go for your option, then I'd look at the config, hopefully it put eth1 and eth2 on the switch, then you can add eth3 and eth4 to the switch as well, and have an outside and 4 insides.

JaredBusch

@Mike-Davis said in EdgeRouter X - bridge mode:

@JaredBusch said in EdgeRouter X - bridge mode:

I would recommend that you wipe and start over using standard port layout.

You can easily reprogram everything by grabbing the output from show configuration commands

I'm headed in... Any reason not to run the WAN+2LAN2 wizard?

Yes, there is a reason not to. That reason is, there is a new 'first run' or something like that on the wizard page. I do not have a ER-X handy to log into to show you the exact name. Assuming you are on the current firmware.

Mike Davis

Thanks @JaredBusch

I went on site and ran the wizard and it was a quick process to fix things. The relevant part of the new config looks like:

interfaces {                                                                    
    ethernet eth0 {                                                             
        address dhcp                                                            
        description Internet                                                    
        duplex auto                                                             
        firewall {                                                              
            in {                                                                
                name WAN_IN                                                     
            }                                                                   
            local {
                name WAN_LOCAL                                                  
            }                                                                   
        }                                                                       
        speed auto                                                              
    }                                                                           
    ethernet eth1 {                                                             
        description Local                                                       
        duplex auto                                                             
        speed auto                                                              
    }                                                                           
    ethernet eth2 {                                                             
        description Local                                                       
        duplex auto                                                             
        speed auto                                                              
    }                                                                           
    ethernet eth3 {                                                             
        description Local                                                       
        duplex auto                                                             
        speed auto                                                              
    }                                                                           
    ethernet eth4 {                                                             
        description Local                                                       
        duplex auto
        speed auto                                                              
    }                                                                           
    loopback lo {                                                               
    }                                                                           
    switch switch0 {                                                            
        address 192.168.1.1/24                                                  
        description Local                                                       
        switch-port {                                                           
            interface eth1 {                                                    
            }                                                                   
            interface eth2 {                                                    
            }                                                                   
            interface eth3 {                                                    
            }                                                                   
            interface eth4 {                                                    
            }                                                                   
        }                                                                       
    }                                                                           
}                                                                               
port-forward {                                                                  
    auto-firewall enable                                                        
    hairpin-nat enable                                                          
    lan-interface switch0
    wan-interface eth0                                                          
}

Solved EdgeRouter X - bridge mode