Dell PERC Question (Server Down)
-
@BRRABill said in Dell PERC Question (Server Down):
@scottalanmiller said
Any why is configuration limited to the BIOS?
I mean the PERC configuration utility access during POST but hitting <CTRL>R.
Me too
-
@BRRABill said in Dell PERC Question (Server Down):
@scottalanmiller said in Dell PERC Question (Server Down):
If it is rebuilding, why is configuration needed? Any why is configuration limited to the BIOS?
Because when this happens, the drives totally disappear from the PERC config and the server crashes. You have to go in and clear the foreign config. There is nothing to rebuild.
It's not like a drive has failed, and the LED is orange and you can pull it. Nothing like that.
That means that the PERC has failed. That's a different issue.
-
@scottalanmiller said
That means that the PERC has failed. That's a different issue.
Are we back to that?
I mean, it's definitely on the table. Just not sure why all of a sudden you think that's so likely.
-
@BRRABill said in Dell PERC Question (Server Down):
@scottalanmiller said
That means that the PERC has failed. That's a different issue.
Are we back to that?
I mean, it's definitely on the table. Just not sure why all of a sudden you think that's so likely.
Because you said that it was rebuilding. The PERC should remain up and viable even without disks attached to it. You can continue to manage it online through the iDRAC or a VM that isn't using those drives.
-
@scottalanmiller said
Because you said that it was rebuilding. The PERC should remain up and viable even without disks attached to it. You can continue to manage it online through the iDRAC or a VM that isn't using those drives.
The PERC is up. It's just the drives aren't. Certain drives aren't. The DELL 7.2K SATA drives I have in an array have not dropped off or made a peep once.
The DRAC isn't so great at managing storage or talking to the PERC, or so I have been told. (Those the remote console is worth its weight in gold)
-
Are you booting from SD card? That would solve the issue, right?
-
@scottalanmiller said
Not yet, but soon.
And yes, I know that if I was booting off USB/SD I could have copied the VM to my other storage repository and then redid my array.
-
@BRRABill said in Dell PERC Question (Server Down):
@scottalanmiller said
Not yet, but soon.
And yes, I know that if I was booting off USB/SD I could have copied the VM to my other storage repository and then redid my array.
Yes, that too. But I also mean that the array could be managed without a reboot.
-
That's anther good reason that we don't normally think of for installing to SD/USB.
-
@scottalanmiller said
Yes, that too. But I also mean that the array could be managed without a reboot.
You can install OMSA to a VM? I didn't think it would be able to access the hardware.
-
@BRRABill said in Dell PERC Question (Server Down):
@scottalanmiller said
Yes, that too. But I also mean that the array could be managed without a reboot.
You can install OMSA to a VM? I didn't think it would be able to access the hardware.
You install directly to XenServer's Dom0 which has hardware access.
-
@scottalanmiller said
You install directly to XenServer's Dom0 which has hardware access.
I was going to ask about this in my roadtrip of XS.
So, then how do you access it? From a web browser just like any other OMSA install?
-
@BRRABill said in Dell PERC Question (Server Down):
@scottalanmiller said
You install directly to XenServer's Dom0 which has hardware access.
I was going to ask about this in my roadtrip of XS.
So, then how do you access it? From a web browser just like any other OMSA install?
Dom0 is just an operating system, CentOS in XenServer. It would host the application as if it were installed on any other server.
-
@scottalanmiller said in Dell PERC Question (Server Down):
That's anther good reason that we don't normally think of for installing to SD/USB.
Did you see my post about the speed of my USB2 booted test XS. It is SO SLOW.
Is that normal since it is USB2?
Would SD be any quicker? though for the few times you update/reboot, perhaps the speed at boot/update isn't an issue.
-
@BRRABill said in Dell PERC Question (Server Down):
@scottalanmiller said in Dell PERC Question (Server Down):
That's anther good reason that we don't normally think of for installing to SD/USB.
Did you see my post about the speed of my USB2 booted test XS. It is SO SLOW.
Is that normal since it is USB2?
Would SD be any quicker? though for the few times you update/reboot, perhaps the speed at boot/update isn't an issue.
No, I missed it. How slow was it?
-
@coliver said
Dom0 is just an operating system, CentOS in XenServer. It would host the application as if it were installed on any other server.
I'm confused as to why it matter you can't administer it if XS boots off the same array, then.
I could access OMSA from my desktop browser.
-
@BRRABill said in Dell PERC Question (Server Down):
@coliver said
Dom0 is just an operating system, CentOS in XenServer. It would host the application as if it were installed on any other server.
I'm confused as to why it matter you can't administer it if XS boots off the same array, then.
I could access OMSA from my desktop browser.
If you were installing it onto an SD card or USB stick it wouldn't matter.
-
@scottalanmiller said
No, I missed it. How slow was it?
Pretty slow. But of course I was going from using a SSD.
It took the good part of an afternoon to install all the updates once I had it installed.
-
@coliver said
If you were installing it onto an SD card or USB stick it wouldn't matter.
Why would that even matter? Unless we are talking some sort of destructive operation to the array...
-
@BRRABill said in Dell PERC Question (Server Down):
@coliver said
If you were installing it onto an SD card or USB stick it wouldn't matter.
Why would that even matter? Unless we are talking some sort of destructive operation to the array...
I guess I'm not following, you were asking how to access something installed on Dom0. Did I misunderstand the question?
